In this fourth part of my ongoing blog series about our new Beastmaster Boats Snubby 500 rig, I reveal the “vital statistics” of the boat and share a few recent images of it in action. If you’d like to read Part 1, click here. For Part 2, click here. And for Part 3, click here. Also, don’t forget that you can watch a short video of the boat’s maiden voyage right here. Okay, down to business!   VITAL STATISTICS: BEASTMASTER SNUBBY 500* LENGTH: 5.0 metres (16′ 6″) BEAM: 1.98 metres (6′ 6″) HULL DEPTH: 0.76 metres (2′ 6″) HULL SIDES: 0.57 metres (1′ 11″) DRAFT: 0.26 metres (10″) DRY HULL WEIGHT: approx. 375 kilos (827 lb) * Explanatory Notes: Measurements quoted are generally to within a few millimetres and all conversions to imperial have been rounded up or down to nearest inch or pound. Hull Depth refers to the maximum depth from gunwale tops/coamings to the deepest part of hull. Hull Sides are flat sides from coamings to chines. Draft (vertical distance between the waterline and deepest part of keel) is an approximate figure (+/- 10%) for the unladen hull and will depend on weight added, load distribution, salinity of water, etc. For this reason, the draft shown should be regarded as a minimum under ideal conditions. Dry Hull Weight is an approximate figure (+/- 10%) and obviously does not include motor, batteries, fuel, electronics, safety gear and other equipment. Next time we’ll have a look at the Yamaha F70A four-stroke outboard fitted to the Snubby, along with the MotorGuide Xi5 bow-mounted electric trolling motor, Lowrance electronics and various other fittings. Until then, tight lines… and meanwhile, here are a few more images of the rig in action:   For more, follow me on...

The Australian Freshwater Masters is a unique tournament series that pitches teams of anglers against each other across a time frame of several months at three very different venues, targeting a trio of iconic native species. Jo and I competed in The Freshwater Masters for the first time in 2015/16, and were fortunate enough to ultimately win the event… Here’s the inside story of exactly how we did it: The Australian Freshwater Masters is an innovative tournament series first conceived by well-known Aussie lure maker, Wayne Lennon, some two decades ago. Wayne successfully ran the annual event for many years before handing the reins to Dave Silva. Later, Dave Shelton picked up the baton and, in more recent times, has been ably assisted by Matt Cunneen, creator of Gangster Lures in Wagga. As of last year, Matt is now running the event largely by himself. The Masters is a brilliant concept, with three rounds taking place on three very different waterways, targeting a trio of our most popular and iconic freshwater natives: golden perch, Australian bass and Murray cod. Teams consist of two anglers, and their cumulative scores carry forward from one round to the next, eventually deciding the overall champions. It’s definitely a concept that rewards versatility, determination and consistency of performance. The Masters is a lure-and-fly only event, with both casting and trolling allowed and, naturally, it’s all about catch-and-release. Live fish are photographed on standard issue Fisheries measuring mats and, where possible, witnessed by another team, although the welfare of the fish always comes first, so if there are no witnesses nearby, a date-stamped digital photo is acceptable. While ostensibly an invitational series, expressions of interest from new teams are invited every year and are generally accepted, at least until the...

In this first installment of my ongoing blog series about our Beastmaster Snubby 500, I look at the decision-making process that went into our selection of this bespoke, custom-built boat: Choosing a boat is always a massive decision. Like most keen anglers who’ve been pursuing their passion for a considerable period of time, I’ve owned a bunch of different vessels. I kicked off with a second-hand fibreglass canoe in my teens, went on to a car-topper aluminium punt, then a Webster Twinfisher alloy cat. That brings us through to an era when I first met shipwright and boat builder, Tyson Dethridge, and fell head over heels for his customised Full Boar fibreglass sportfishers, running first a 5 metre version, then a 5.5. Next, I spent a year or two in a fully imported Scout flats boat from the U.S. That was followed by a neat little 4.1 metre tiller-steer Cross Country (again built by Tyson) before I graduated into one of his larger, centre-console 4.75 metre Cross Country rigs. That 4.75 Cross Country (called “Evil Minnow” after one of the deadliest Squidgies soft plastic colours) was part of our family for well over six years, and we absolutely loved it. I’d have to say it was my favourite boat up until that point. With its light-but-strong foam-core sandwich fibreglass construction and powered by a class-leading F70A Yamaha 4-stroke motor, this was quite a radical craft, especially in Darwin, where we lived at the time. I reckon it opened a few alloy-blinkered Top End eyes to the validity and surprising durability of good glass. Our 4.75 Cross Country was the prototype of that hull and it had a few “rough edges” internally, but it served us exceptionally well. We dragged it over some bloody awful...

The third and final round of the hard-fought Australian Freshwater Masters tournament series was staged in mid-February this year on the waters of Lake Mulwala, a picturesque impoundment straddling the NSW/Victorian border, an hour or so west of Albury. This unique, three-stage challenge targets a trio of iconic Australian native species at three very different venues. The first round of the latest Freshwater Masters took place last November on Lake Windamere, near the NSW regional town of Mudgee, and was devoted to the pursuit of golden perch or yellowbelly. A few days later, round two was staged on Glenbawn Dam, in the Hunter Valley, with Australian bass as the nominated target species. Finally, almost three months later, competitors gathered at Lake Mulwala to hunt the elusive Murray cod. A catch-and-release series devoted entirely to lure and fly fishing, The Australian Freshwater Masters challenges its field of two-person teams to measure, photograph and release up to 10 legal specimens of each target species at each arena over the course of two days’ of intensive fishing. Cumulative point scores (one point per millimeter) carry forward from round to round, ultimately deciding the outcome of the event. This year, the eventual winners were Team Starlo’s Squidgies, consisting of high profile fishing communicator, Steve ‘Starlo’ Starling, and his wife Jo. Consistent performances in rounds two and three allowed Starlo and Jo to hold onto the significant lead they’d amassed on Windamere’s goldens in round one (where Jo was also the individual champion angler), finally giving them an 800 point break over the second-placed Jigheads Team of Mitchell Skeers and Brad Gardiner. A further 1,300 points behind in third place was Team Windybanks, made up of Simon McAlpine and David Dobson. Overall Champion Angler for the Masters was Mitchell...

Lots of anglers still struggle to crack the bream-on-lures code. Truth is, these fish are no pushover. But if you follow my simple, five-point plan below, and watch the accompanying video clip here, I’m confident you’ll be posing for a photo with your first bream on a soft plastic very soon! As I travel the country fishing, researching stories and gathering material for this blog and the many publications I contribute to, I come across increasing numbers of anglers who’ve embraced lure fishing and, in particular, the use of soft plastic lures. The uptake of soft plastics has definitely been one of the most significant trends in Australian recreational angling over the past 10 to 15 years, and its popularity shows no sign of diminishing any time soon. Softies are great lures and they’re not all that hard to use. Most new chums start catching at least the odd fish very early in their plastic-flicking careers. But some species are tougher nuts to crack than others, and the humble bream is perhaps the trickiest of the lot. It’s also the one I get asked about the most. The question typically begins with a statement along the lines of: “I can catch plenty of flathead on plastics, but I’m damned if I can work these bream out!” If you’re in that camp, I’m here to help! Below I’ve listed a simple, five-step strategy for cracking the bream-on-plastics code, and this is accompanied by this short, no-nonsense how-to video clip on my “Starlo Gets Reel” YouTube channel. You can go straight to that video by scanning the QR code at the bottom of this page, or by typing this URL into your browser: www.youtube.com/watch?v=8wuLI5-M3UQ Okay… Are you ready to learn how to catch your very first...

The “Lure of Trout” live-in workshop that Jo and I ran at Lake Crackenback Resort & Spa in the Australian Snowy Mountains during early November, 2014 was a great success and seems to have been enjoyed enormously by all participants. Watch the short video below for a taste of the workshop’s highlights. We’re planning more of these residential workshops for 2015 and beyond, so if you’d like to be involved, lodge an obligation-free expression of interest by clicking here. You should also check out our other hosted trips to exciting destinations by clicking here....

For those who missed it. I’ve attached my recent feature on catching big bream on flies from “Barra, Bass & Bream Digest” magazine. And in case the text from the magazine layouts is too small to read on your screen or in this format, I’ve also included the straight text at the bottom of this blog post. Also, if you’d like to find out how to purchase or subscribe to “Barra, Bass & Bream” on-line, go to: http://www.nafa.com.au/ Big Bream On Fly The Ultimate Challenge? What’s the ultimate prize in modern day barra, bass and bream fishing? Catching a metre-plus ’mundi on a surface lure and light tackle? Landing a 60 cm wild bass from a kayak? Pulling a 2 kg bream onto a wave-washed rock ledge in the middle of the night? Starlo rates all of those milestones, but reckons there’s another one that presents even more of a challenge. In his opinion, mastering big bream on fly is the toughest (and perhaps the most rewarding) game in town… Read on and see if you agree! The average, weekend angler no doubt struggles to understand why some of us might actually choose to make our fishing any harder than it needs to be. For many hopefuls, simply catching a feed of fish is a daunting enough prospect, without deliberately adding extra layers of difficulty to the process. Yet, as with any endeavour, those who are seriously engrossed in their passion and spend a lot of time pursuing it eventually look for extra layers of challenge: new peaks to scale and higher marks to attain. In preparing to write this feature, I spent considerable time pondering the bigger challenges fishing has presented me with over the years. In my late teens and early 20s,...

Check out this great clip produced by the guys at “The Offroad Adventure Show”! [youtube=http://www.youtube.com/watch?v=uBrTANhJZMQ&w=420&h=315]  

Most modern fishing reels, regardless of their style or type, are equipped with a drag or “slipping clutch” mechanism of some sort that allows line to be pulled from the reel’s spool under a pre-set tension. On a threadline or spinning reel, drag pressure is usually adjusted via a knob located on the front of the spool or (more rarely) under the rear of the reel’s body. Overheads and baitcasters either have a star wheel under the handle or a lever on the side of the reel for adjusting the drag, while sidecasts and centrepins typically feature a nut or star in the centre of the spool. This drag is intended to prevent the line from breaking should excessive force be placed upon it. Instead of snapping, line slips from the spool against the pre-set drag tension. When a large or powerful fish is hooked, it usually needs to be “played” using a combination of drag resistance and rod work. The term “playing a fish” means taking your time and bringing the fish in more slowly and smoothly while using the flex of the rod as a shock absorber. If necessary, you will also need to allow the hooked fish to “run”: in other words, to pull line from the spool against the reel’s pre-set drag or slipping clutch. This may happen many times during a fight with a strong adversary, especially on lighter line. A big, strong fish can easily pull the rod tip down and rip line off the spool against the resistance of the reel’s drag. However, if the drag has been set too tightly, the line can possibly snap, or the hook might bend or straighten and rip out of the fish’s mouth. On the other hand, if the drag...

For those who missed it first time around in print, here’s a piece on open water bream luring that first ran in FishLife magazine earlier this year: The art of luring bream has been one of the major engines of change in Australian sport fishing over the past few decades. In less than a single generation, catching bream on lures has gone from being an accident or a novelty for most anglers to a regular pursuit for many. Even those who don’t “get it” and wonder what all the fuss is about must grudgingly admit that the pursuit of bream on artificial baits has completely transformed our sport. Before many of you reading these words were born, that doyen of Australian fishing writing, Vic McCristal, offered the opinion that anglers skilled enough to regularly take bream on lures would tend to find most other species easy. It was McSea’s quietly understated way of doffing his cap to the bream clan as perhaps our most challenging piscatorial targets. What Vic could hardly have guessed in those days was the passion with which this country’s sport fishing community would eventually embrace that particular challenge, and how doing so would completely revolutionise our tackle, our techniques and even our angling mindset. Make no mistake: bream luring has radically altered the shape of Australian fishing, and this significant evolutionary upheaval is far from having run its course. Discoveries remain to be made. For many, open water breaming is just one of them. Middle Of Nowhere For most of us, thoughts of catching bream on lures immediately conjure mental images of structure fishing: accurately casting our soft plastics and little hard bodies at shorelines, rocks, snags, pylons, oyster lease racks or moored boats. But what if I told you...

In mid-September, 2012, my wife Jo and I were lucky enough to sample the extraordinary fishing on offer around the remote Cobourg Peninsula, north east of Darwin, as guests of a wonderful operation called Venture North Australia. Owned and run by affable brothers Aaron and Hugh Gange, Venture North has historically been an eco-tourism, wildlife and cultural-experience guiding operation offering a little casual fishing on the side (usually aimed at catching dinner). However, earlier in 2012, all that changed with their purchase of a Darwin-built, 7-metre CustomWorks Eliminator plate alloy sportfishing boat powered by a 225 HP Yamaha four-stroke. To say the boys have made a decision to take the fishing side of their business a lot more seriously would be something of an understatement! Interestingly, my good lady Jo was partly instrumental in this significant upgrading of Venture North’s fishing focus. While looking at the Gange brothers’ website in her role as a marketing consultant, Jo noticed quite a few photos of big fish. She asked why they didn’t place more prominence on this aspect of their operation, and her comments obviously got the guys thinking! Less than a year later they’d bitten the bullet, bought the big boat and significantly ramped up the angling side of the business. As something of a thank-you to Jo for her advice, Aaron and Hugh invited her up to Cobourg for a few days, and mentioned that she might as well bring her old man along, as apparently he didn’t mind a spot of fishing, either! Back to Cobourg As our light plane banked in over the broad, sparkling expanse of Cobourg’s Port Essington, I reflected that it had been at least 25 years since my last visit to this fantastic part of the world… Far...

Over the course of a year, I get to talk to a lot of soft plastics fishers from around the country. Some I meet at seminars and shows. Others I chat with via the various pages on Facebook that I run or help to administer (especially the StarloFishing, Fishingscool and Squidgy Soft Plastics pages), or through my blogs here at www.starlofishing.me Still others send their letters or emails to me via the magazines I write for. However, no matter what the source of the enquiry, one question (or variations of it) dominates the calls for advice that I receive. Typically, that query begins with the words: “What’s the best soft plastic for…?” The rest of that sentence almost always contains a species of fish and a precise location: What’s the best soft plastic for bream in the Patterson Lakes? What’s the best soft plastic for trout in the Murrumbidgee River? What’s the best soft plastic for flathead on the Gold Coast? What’s the best soft plastic for yellowbelly in the Murray? What’s the best soft plastic for redfin in Lake Eildon? What’s the best for barra in the Daly? And so on… I can’t help but smile at the geographic specificity of these well-meaning questions. Anglers clearly have their favourite fishing spots and they seem to expect that the fish they chase in these beloved haunts will behave just a little differently to those living down the road, around the bend or across the border. Generally speaking, this is not the case. I’ve caught redfin perch in the New England rivers of north western NSW, and also in the very “old England” rivers around the historical university city of Cambridge, in Great Britain (where they’re simply known as perch). Rather unsurprisingly, these fish looked...

In my last two blogs in this series I’ve been exploring the exciting subject of customizing your soft plastic lures to alter their actions, colours and sink rates in order to better suit specific applications, fishing scenarios and target species. As I explained in both of those blogs, this entire subject area of customizing plastics is a branch of tackle tinkering that far too few Aussie anglers appear willing to experiment with. Many seem to believe that these lures must be used in exactly the form supplied for sale by the manufacturer. But as we’ve been discovering, that’s not the case at all! In fact, nothing could be further from the truth. Unlike most hard-bodied offerings, softies lend themselves extremely well to individual input and fine tuning from the angler, allowing you to clearly stamp your own personal identity and fishing preferences on the lures you use. In the first blog on Customising Soft Plastics, I focused on tweaking colours and patterns using various dyes and marker pens to achieve specific results, whether attempting to “match the hatch”, suit the environment, stand out from the pack or simply emulate a successful hard-bodied lure finish. Last time around, in Part 2, we pulled out the scissors, razor blades and hobby knives and started playing with the actual shape, bulk and profile of these versatile lures to adjust their actions, overall sizes and sink rates. This time, I want to look at the intriguing subject of lure hardness and its impact on action, “mouth feel” and durability. So, let’s kick off by tackling the subject of relative hardness in soft lure materials: TO READ THE REST OF THIS BLOG & OTHERS IN THE SERIES, CLICK...

It’s time to continues our look at customising your soft plastic lures with an examination of easy ways in which the size, profile, sink rates and actions of these great lures can be tweaked and manipulated via some simple cutting and shaping: In my last blog about customising soft plastics I explained that this is an avenue of tackle tinkering that too few anglers seem willing to explore. Many seem to assume that these lures must be used in exactly the form they were originally purchased in. Trust me, that’s certainly not the case! I theorized that this hands-off approach to tweaking plastics is most likely a hangover from our hard-bodied luring days. Beyond possibly upgrading some hooks and rings, very few anglers significantly modify their hard lures. But soft plastics are much easier to customise than hard lures, and doing so can produce some surprising results. The big secret is not to be afraid to give it a go! Last time round I focused on “blinging” your plastics by using various dyes and marker pens to alter or enhance their colours and patterns. This time I want to take customising one step further and actually get into playing with the shapes, sizes, profiles, sink rates and actions of our soft plastics. To do this, all you really need is a sense of adventure and a pair of sharp scissors. Making that first step of actually taking the scissors or craft blade to your plastic tails is perhaps the biggest leap of faith required to get into customizing soft plastics. After that, it gets much easier. TO READ THIS BLOG IN FULL & ACCESS OTHERS IN THE SERIES, GO TO “STARLO’S INNER CIRCLE” BY CLICKING...

Rigging your Squidgies and other soft plastic lures “weedless” or “snag-proof” is much easier than many people seem to think! And once they’re rigged this way, it’s possible to cast these lures into places you could never otherwise reach or cover effectively without constantly snagging up your line and losing expensive tackle. Trust me, you’ll catch a lot more fish as a result of adding this little trick to your rigging repertoire. These days, at least 75 – 80% of the plastics I cast for barramundi and saratoga in northern Australian waters are rigged weedless/snag-proof. But these innovative rigging strategies go far beyond those species. The same approach works like a charm on any fish that favours hanging out in or around dense snag, rock or weed cover. Bream, bass, estuary perch, flathead, mangrove jack, fingermark, Murray cod, golden perch (yellowbelly) and even trout can all be targeted very effectively by “Texas-rigging” your softies on wide-gape worm hooks. The most important part of this rigging  system is a wide-gaped worm hook, or a jig head or other delivery vehicle that incorporates a wide gape worm hook. These hooks may look a bit odd at first glance, but they work really well. Lots of companies now make this style of hook. Some good ones include Mustad, Owner, Gamakatsu, and VMC. One really interesting new addition to the wide gape worm hook field is the KVD Grip-Pin hook from Mustad. This clever hook incorporates a little pin that helps keep the head of the rigged plastic in place, preventing it from being too easily ripped free or scrunched down into the hook bend by a striking fish. Another very innovative presentation vehicle for this style of rigging is the TT Lures Snake Head. The best way to...